Industrial Ethernet switch for control panels, security cabinets and plant rooms. Plug-and-play unmanaged switching in 5 or 8 ports, Fast Ethernet or Gigabit. Dual redundant 12–52 VDC inputs, 2 kV network surge protection, full metal IP40 housing, fanless cooling and −30 °C to +70 °C operation on 35 mm DIN rail.
Industrial Ethernet switch built for control panels, outdoor cabinets and plant rooms where a standard office switch won’t last. The DTECH SW1000 Series is a plug-and-play unmanaged switch in 5-port and 8-port versions, available in 10/100 Mbps Fast Ethernet or 10/100/1000 Mbps Gigabit, so you can match the switch to the job instead of over-specifying it.
Dual redundant 12–52 VDC power inputs keep the network running if one supply fails. A full metal IP40 housing, fanless cooling and a −30 °C to +70 °C operating range make it a dependable choice for automation panels, security cabinets and unconditioned equipment rooms across the Gulf. Why Choose an Industrial Ethernet Switch?
Commercial desktop switches are designed for air-conditioned offices. Inside a control cabinet, they face heat, dust, electrical noise, surges and DC power rather than a wall socket. They also sit loose on a shelf, so installers end up cable-tying them to the back of a panel.
An industrial Ethernet switch is designed for that environment from the start. The SW1000 clips onto a 35 mm DIN rail, runs from the 12, 24 or 48 VDC supply already in the panel, and cools passively with no moving parts to wear out. Surge and ESD protection on the power and network ports helps protect PLCs, cameras and controllers on the other end of the cable. For system integrators and contractors, that means a cleaner panel build, fewer callbacks and a network that keeps automation and monitoring equipment talking.
Plug-and-play, zero configuration: connect devices and go. No IP setup, software or network engineer needed on site.
Four models to fit the job: 5 or 8 ports, in 10/100 Mbps Fast Ethernet or 10/100/1000 Mbps Gigabit.
Redundant dual power input: two 12–52 VDC inputs keep the switch running if one power supply fails, with reverse polarity protection.
Line-rate forwarding: full-port line-rate transmission with low latency, up to 16 Gbps switching capacity on the 8-port Gigabit model.
Enhanced surge and ESD protection: 2 kV common-mode surge protection on network ports and ±6 kV contact / ±8 kV air ESD protection.
Full metal IP40 housing: robust construction for control cabinets and enclosures.
Fanless natural cooling: no fan to fail, collect dust or add noise.
Industrial temperature range: operates from −30 °C to +70 °C.
High reliability: MTBF of at least 300,000 hours for long, low-maintenance service.
Compact DIN rail design: 94 × 76 × 26 mm (5-port) or 110 × 91 × 40 mm (8-port).
Brand: DTECH
Series: SW1000
Product type: Unmanaged DIN rail industrial Ethernet switch
Models:
SW1000-5FT-BU-2D: 5 × 10/100Base-TX RJ45 ports
SW1000-8FT-BU-2D: 8 × 10/100Base-TX RJ45 ports
SW1000-5GT-BU-2D: 5 × 10/100/1000Base-T RJ45 ports
SW1000-8GT-BU-2D: 8 × 10/100/1000Base-T RJ45 ports
Switching capacity: 1 Gbps (5FT), 1.6 Gbps (8FT), 10 Gbps (5GT), 16 Gbps (8GT)
Packet forwarding rate: 7.5 Mpps (5 port), 11.904 Mpps (8 port)
Buffer memory: 1.2 Mbit (5-port), 2 Mbit (8-port)
MAC address table: 4K
Jumbo frame: 9 Kbit
Port operating mode: half-duplex, full-duplex, auto-negotiation, auto MDI/MDI-X
Standards: IEEE 802.3, IEEE 802.3u, IEEE 802.3x (plus IEEE 802.3ab on Gigabit models)
LED indicators: power, network
Input voltage: dual DC 12–52 V (rated 12/24/48 VDC)
Power connector: 5.08 mm pluggable terminal block
Reverse polarity protection: supported
Surge protection: power port 1 kV common-mode / 0.5 kV differential-mode; network ports 2 kV common-mode / 1 kV differential-mode
ESD protection: ±6 kV contact, ±8 kV air
Operating temperature: −30 °C to +70 °C
Storage temperature: −40 °C to +80 °C
Operating humidity: 10–90% RH, non-condensing
Storage humidity: 5–95% RH, non-condensing
Housing: full metal
Ingress protection: IP40
Cooling: fanless natural cooling
Mounting: 35 mm DIN rail
MTBF: ≥300,000 hours
Dimensions (W × D × H): 94 × 76 × 26 mm (5 port), 110 × 91 × 40 mm (8 port)
Package contents: 1 × industrial Ethernet switch, 1 × 5.08 mm wire terminal, 1 × product manual
PLC and machine vision: connect PLCs, HMIs and industrial inspection cameras on production lines with low latency.
CNC machines and industrial robots: add network ports at workstations without running new cables back to the main switch.
AGVs and intelligent warehousing: network automated storage and logistics equipment.
Industrial IoT: connect edge gateways, sensors, protocol converters and RS485-to-Ethernet servers back to the main network.
Security and IP surveillance: network IP cameras, NVRs and access control panels in car parks, campuses and perimeter enclosures.
Utilities and infrastructure: link wastewater treatment equipment, outdoor power distribution cabinets and pumping stations.
Building management and MEP: network BMS controllers, energy meters and plant room equipment.
Fast Ethernet (FT models) suits PLCs, HMIs, meters, sensors and most control equipment, which rarely need more than 100 Mbps. It is the cost-effective choice for automation panels.
Gigabit (GT models) suits IP cameras, machine vision, NVRs and uplinks carrying traffic from several devices. Choose Gigabit when video or large data transfers share the network.
The 5-port industrial Ethernet switch suits small machine networks, single cabinets or a camera pole with a few devices. The 8-port industrial Ethernet switch suits larger panels and sites where you expect to add devices later. Spare ports now save a second switch and a rewire down the track.
If you are unsure which model suits your project, send BAM your device count and site conditions, and our team will recommend the right one.
Clip the industrial Ethernet switch onto a 35 mm DIN rail and connect the earth (FG) terminal to a reliable ground, which is essential for surge and anti-static performance. Wire the power to the V+ and V− terminals from a 12, 24 or 48 VDC supply, and double-check polarity before switching on. For redundancy, connect a second supply to the second power input. Use shielded Ethernet cable in electrically noisy areas and route data cables away from motor and high-voltage power cabling.
For background on the technology, see this overview of industrial Ethernet (https://en.wikipedia.org/wiki/Industrial_Ethernet) and the manufacturer’s product page (https://www.dtechelectronics.com/dtech-industrial-ethernet-switch-5-8-port-unmanaged-industrial-ethernet-switch-for-industrial-automation_p685.html).
Bait Almajara Trading L.L.C. (BAM) is the Middle East distributor for DTECH, supplying system integrators, MEP and electrical contractors, facility management companies and procurement teams across the UAE, GCC, Africa and Central Asia. We offer project pricing, bulk quantities and technical support for industrial networking and serial communication projects.
Pair this switch with the DTECH IOT9024DI Isolated RS485 Hub, and explore more in our IoT and Industrial Serial range, including RS485 converters and serial-to-Ethernet servers.
For quotations or project enquiries, contact sales@bam.ae or WhatsApp +971 52 374 3008. Frequently Asked Questions
It is a network switch designed for harsh environments such as control panels, factories and outdoor cabinets. Compared with an office switch, it mounts on a DIN rail, runs on DC power and is built to handle heat, dust, surges and electrical noise.
An unmanaged switch works straight out of the box with no configuration. You connect your devices, and it forwards traffic automatically, which makes installation quick and avoids setup errors on site.
Fast Ethernet (10/100 Mbps) is enough for PLCs, HMIs, meters and most control devices. Choose Gigabit (10/100/1000 Mbps) for IP cameras, machine vision, NVRs or uplinks carrying traffic from many devices.
Yes. Every SW1000 industrial Ethernet switch has dual 12–52 VDC power inputs, so the switch keeps running if one supply fails.
It operates from −30 °C to +70 °C in 10–90% RH non-condensing humidity. With an IP40 rating, it should be installed inside a suitable enclosure or control cabinet, not exposed directly to rain or dust.
No. The SW1000 is a standard industrial Ethernet switch, so IP cameras and other devices need their own power supply.
Share your thoughts with other customers
WhatsApp us
Reviews
There are no reviews yet.